STREAMS

CE=CIVIL ENGINEERING, CECA=CIVIL ENGINEERING WITH COMPUTER APPLICATION, ME=MECHANICAL ENGINEERING, AMIA=ADVANCED MECHATRONICS AND INDUSTRIAL AUTOMATION, EE=ELECTRICAL ENGINEERING, ECSE=ELECTRICAL & COMPUTER ENGINEERING, CSE=COMPUTER SCIENCE & ENGINEERING, ECE=ELECTRONICS & COMMUNICATION ENGINEERING

STUDENTS WITH STATUS – “SELECTED” FOR SPECIFIED BRANCHES MUST COMPLETE THEIR ADMISSION FROM 1ST JULY 2024 TO 6TH JULY 2024 (10:00 A.M TO 5:00 P.M) WITH FULL PAYMENT OF FEES ONLY AT TCEA CITY OFFICE (RAMNAGAR- Road No. 02, T.G Road, Beside Eastern Commerce.)

SEARCH BY YOUR ROLL NUMBER TO KNOW YOUR STATUS

ALL ADMISSIONS FOR B.TECH LATERAL ENTRY FOR TCEALET 2024 SHALL ONLY BE DONE AT TCEA CITY OFFICE ONLY.

INSTRUCTIONS FOR TCEALET 2024 WAITLISTED CANDIDATES:

1. Wait-listed Candidates shall be called for admission to B.Tech Lateral Entry  depending on the number of available seats in the respective branch.

2. Wait-listed candidates who are invited to counseling must report to TCEA CITY OFFICE ONLY , upon first come first serve basis with original copies of the following documents and full fees. i) Madhyamik Mark sheet ii) Diploma Mark sheets from 1^st to 5^th Semester/6^th Semester iii) TCEALET Admit Card iv) Madhyamik Admit/Birth Certificate v) PRTC vi) ADHAAR Card  vii) Caste Certificate (if applicable) viii) PAN Card (Self/Guardian)

3. Candidates will be admitted through first come first serve basis only as per published result status.

4. Waiting list Candidates chosen for admission will be required to pay the full requisite fee for admission on the spot, so all candidates are advised to be prepared for this.

5. Mere selection for the waitlist does not guarantee admission. After verification of original certificates/documents, admission will be given only if they fulfil all the eligibility criteria and pay relevant fee. Their selection stands cancelled in case they fail to produce the original certificates mentioned below at the time of verification or fail to pay the relevant fee.

TCEALET (TCEA Lateral Entry Test) is conducted by Techno College of Engineering Agartala for admission into Lateral Entry  (3rd semester) of B.Tech degree program for those students who have completed three years Diploma in relevant branches or Candidates passed B.Sc. with 45 % Marks in average and passed 10+2 with Mathematics as a subject.

The aforesaid Examination shall be conducted on 30th June, 2024 (Sunday) at Techno College of Engineering Agartala Campus from 11:00 AM to 12:30 PM .

Last date of registering for TCEALET 2023 (ONLINE/OFFLINE) is 28th June, 2024.

FOR ANY FURTHER INFORMATION CONTACT US @ 6033392796, 6033392797, 6033392798

Date of Exam :- 30/06/2024

REPORTING TIME AT COLLEGE : 9:30 AM

[CANDIDATE NEEDS TO CARRY A VALID PHOTO ID PROOF FOR APPEARING THE EXAMINATION. PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE APPEARING THE TEST]

Time Of Exam: 11:00 AM to 12:30 PM .

ADMIT CARD WILL BE DISTRIBUTED ON THE SPOT BEFORE EXAM STARTS

SEARCH BY YOUR NAME TO KNOW YOUR ROLL NO.

IMPORTANT INSTRUCTIONS TO THE CANDIDATES:\

1. Mobile Phones, Electronic gadgets shall not be allowed inside the Examination Hall.

2. OMR Sheet should be carefully filled by using BLACK Ball Pen Only.

3. Candidates must report at the Examination Centre atleast one hour prior to scheduled time of Examination.

4. Admit cards shall be available at the exam venue on the day of the examination. However Roll Numbers of the candidates shall be available in the website, two days prior to the date of examination.

5. Candidates shall not be allowed to leave the exam hall till the completion of the examination.

6.Candidates would not be allowed to enter the examination room after the commencement of the examination.

7. 0.25 marks shall be deducted as penalty for each wrong answer or incase more than one option is selected.

8. Use of any sort of unfair means during the examination shall automatically lead to the disqualification of candidature.

9. Decision of the Competent Authority shall be treated to be final.

LAST DATE OF REGISTRATION (ONLINE/OFFLINE) IS 28/06/2024

OFFLINE FORMS CAN BE COLLECTED AND SUBMITTED EITHER AT TCEA CAMPUS OR TCEA CITY OFFICE.

• MODE OF EXAM:  OFFLINE

•  

• VENUE: TECHNO COLLEGE OF ENGINEERING AGARTALA CAMPUS

•  

• DATE: 30/06/2024

•  

• TIME: 11:00 AM to 12:30 PM

•  

• TOTAL MARKS: 60

•  

• PATTERN OF QUESTION:  MCQ BASED

•  

• TOTAL DURATION: 90 MINUTES

TECHNO COLLEGE OF ENGINEERING LATERAL ENTRY (TCEALET) SYLLABUS

E N G I N EE R I N G M E C H A N I C S
Introduction
Concept of Engineering Mechanics — Statics & Dynamics — Scalar Quality — Vector Quality — Addition
& Subtraction of Vectors — Basic units — Derived Units — SI units — principles of dimensional
homogeneity.
System of Forces
Definition of a force with explanation — Linear representation of force — System of co-planar forces —
Parallelogram Law of Forces — Composition and Resolution — Transmissibility of forces — Action and
Reaction — Triangle Law & Polygon Law of forces — Determination of Resultant by Analytical and graphical
method with equalitarian space diagram — Vector diagram.
Moments & Couples
Definition of moment of a force about a point — Physical significance of moment — Moment of a system of
parallel and inclined forces — Varignon’s Theorem — Definition of moment of a couple — Physical
significance of Couples Equivalent couples — Resultant of any number of coplanar couples — Replacement of
a force about a point by an equal like parallel force together with a couple — properties of couples.
Condition of Equilibrium
Lami’s Theorem — Triangle Law & Polygon Law of equilibrium — Conditions of equilibrium of co-planer
system of concurrent forces — Conditions of equilibrium of co-planar system of non-concurrent parallel forces
(like & unlike) — Conditions of equilibrium of co-planar system of non-concurrent non-parallel forces (simple
problems excluding statically indeterminant).
Friction
Definition — Useful and harmful effects of friction — Laws of Static friction — Co-efficient of friction —
Angle of friction — Angle of repose — Equilibrium of a body on a rough inclined surface with and without
external force.
Centre of Gravity
Concept & definition — Centre of mass — Centroid – Methods of finding out centroids of simple area by:
(i) Geometrical consideration, (ii) Method of Moments. [** Method of integration should be learnt in strength
of materials on 2nd Semester] — Finding the centroid of the following areas by any method:
(i) uniform triangular lamina, (ii) uniform rectangular lamina, (iii) uniform circular lamina. — Finding the
centriod of the following sections using the method of moment:
(i) T-section, (ii) equal and unequal angle-sections, (iii) equal and unequal I-sections, (iv) different cut-out
sections. 

Moment of Inertia
Introduction — definition and unit — M I of a lamina — Theorems of finding out M I by:
(i) Parallel axis theorem, and, (ii) Perpendicular axis theorem. — Radius of Gyration — Finding out M I of the
following sections using formula only:
(i) Rectangular section, (ii) Square section, (iii) Circular section, (iv) Triangular section. — M I of irregular
areas such as I-sections, T-sections, — Related simple problems. — Polar M I.
Simple Machines
Definition of Machine — Difference between Machine & Lever — Mechanical Advantage, Velocity Ratio and
Efficiency with their relationship — Frictional Effort Load — Condition of reversibility / irreversibility —
Law of Lifting Machines – Maximum mechanical advantage – Maximum efficiency — Effort vs. load curve
— Efficiency vs. load curve — Different types of lifting machine with their mechanical advantage, velocity
ratio & efficiency such as wheel and axle (simple & differential), Crab winch (single & double purchase),
Weston pulley block, worm & worm wheel, simple screw jack.

Rectilinear Motion
Motion equations (with deduction S= V x t: V = u ± f t ; S = u.t ± ½ f t 2
; V2 = U2
± 2 f S) – Newton’s Second
Law of linear motion p = mf (deduction) — Conservation of momentum of a body — No Numerical
problems.
Curvilinear Motion
Angular displacement — Angular speed — Angular velocity — Relation between angular speed & angular
velocity — Angular acceleration — Relation between linear & angular velocity — Relation between linear &
angular acceleration — Centripetal and centrifugal force (numerical problems)
Work Power Energy
Definition, Units, potential Energy (mgh); Kinetic Energy (1/2 mv^2), Laws of conservation of energy. —
Change of Kinetic energy = work done by acting force. Simple numerical problems

S T R E N G T H O F M A T E R I A L S
Simple Stresses & Strains
Scope of subjects. Use of structure, importance of knowledge of stress, strain and deformation in structure,
safety and economy. Engineering materials : definitions and examples — Mechanical properties of engineering
materials: Elasticity, Plasticity, Ductility, Hardness, Fatigue, Creep Brittleness ( definition, examples and
applications). — Stress and Strain: Tensile, Compressive , Shear — Stress-strain diagram: Principles of tensile
testing in universal testing machines showing salient points such as elastic limit, proportional limit, yield
points, breaking points etc., ultimate stress, working stress and factor of safety. — Stress – strain relations:
Hooke’s law, Young’s Modulus, Modulus of rigidity. Poisson’s ratio.
Shear Force & Bending Moment
Definition and Types of beams, supports and loads. — Shear force and bending moment in beams: Definitions,
sign conversions and inter-relationships — Shear force and bending moment diagrams (with simple problems):
(i) Cantilever beams with point loads and Uniformly Distributed Loads (UDL). (ii) Simply supported beams
with point loads and UDL. (iii) Simply supported overhanging beam with point load.
Bending Stresses in Beams
Pure bending of beam: Assumptions, deduction of bending equation with usual notations, moment of
resistance, section modulus. — Problems on bending stress about axis parallel to the plane of bending: for
rectangular circular & I-section

Deflection of Beams
Differential equation of elastic curve — Relation among deflection, slope, shear force, bending moment and
rate of loading — Sign convention of slope and deflection.
Standard formula (no proof, only simple problems) for maximum slope of deflection of: —
Cantilever beam subjected to point load at free end, uniformly distributed load on entire span;
Simply supported beam carrying a point load at mid span, uniformly distributed load on entire span.
Columns & Struts
Definitions of Columns & Struts — Long, Medium & Short columns – Effective Length – Slenderness Ratio –
Critical load – Safe load — Different kinds of end conditions — Euler’s formula for critical load (no
deduction and no problem).

E N V I R O N M E N T A L E N G I N E E R I N G
Introduction
Man & Environment: Overview (socio-economic structure & occupational exposures) – Scope of
Environmental Engineering – pollution problem due to urbanization & industrialization.
Air Pollution
Causes of air pollution – types & sources of air pollutants – Climatic & Meteorological effect on air pollution
concentration – formation of smog & fumigation.
Analysis of Air Pollutants
Collection of Gaseous Air Pollutants – Collection of Particulate Pollutants – Analysis of Air Pollutants like:
Sulphur dioxide – Nitrogen oxide – Carbon monoxide – Oxidants & Ozone – Hydrocarbons – Particulate
Matter
Air Pollution Control Measures & Equipment
Control of Particulate Emission – Control of Gaseous Emission – Flue Gas Treatment Methods: Stacks
Gravitational and Inertial Separation, Settling Chambers, Dynamic Separators, Cyclones, Filtration, Liquid
Scrubbing, Spray Chambers, Packed Towers, Orifice and Venturi Scrubbers, Electrostatic Precipitators,
Gas/solid Adsorption, Thermal Decomposition
Methods & Approach of Air Pollution Control
Controlling smoke nuisance — Develop air quality criteria and practical emission standards — creating zones
suitable for industry based on micrometeorology of air area — introducing artificial methods of removal of
particulate and matters of waste before discharging to open atmosphere.
Water Sources
Origin of wastewater — Type of water pollutants and their effects
Different Sources of Water Pollution
Biological Pollution (point & non-point sources) – Chemical Pollutants: Toxic Organic & Inorganic Chemicals
– Oxygen demanding substances – Physical Pollutants: Thermal Waste – Radioactive waste – Physiological
Pollutants: Taste affecting substances – other forming substances
Water Pollution & its Control
Adverse effects on: Human Health & Environment, Aquatic life, Animal life, Plant life — Water Pollution
Measurement Techniques – Water Pollution Control Equipments & Instruments – Indian Standards for Water
Pollution Control.
Soil Polluting Agencies & Effect of Solution
Liquid & Solid Wastes – Domestic & Industrial Wastes – Pesticides – Toxic: Inorganic & Organic Pollutants –
Soil Deterioration – Poor Fertility, Septicity, Ground Water Pollution, Concentration of Infecting Agents in
Soil.

Solid Waste Disposal
Dumping domestic & Industrial Solid Wastes: Advantages & Disadvantages – Incineration: Advantages &
Disadvantages – Sanitary Land Field: Advantages & Disadvantages – Management of Careful & Sanitary
Disposal of Solid Wastes
Noise Pollution & Control
Noise Pollution: Intensity, Duration – Types of Industrial Noise – Ill effects of Noise – Noise Measuring &
Control – Permissible Noise Limits
Environmental Legislations, Authorities & Systems
Air & Water Pollution Control Acts & Rules (Salient Features only) – Functions of State / Central Pollution
Control Boards – Environmental Management System: ISO 14 000 (Salient Features only)

E N G I N E E R I N G M A T H E M A T I C S
Matrix & Vector
Matrix – Definition – Order of a matrix – Leading element – Principal diagonal. Types of matrices – Null
matrix – Square matrix – Identity matrix – Upper and lower triangular matrix – Symmetric matrix. –
Determinant of a square matrix – Minors and cofactors – Procedures for evaluation – Properties of
determinants (no deduction) – Evaluation of determinant by Chio’s method (4th order) – Problems. –Concept of
vector – Addition and subtraction of vectors – Multiplication of a vector by a scalar – Position vector of a point
– Ratio formula – Rectangular resolution of a vector – Dot and cross product – Geometrical interpretation –
Distributive law – Applications.

Numerical Methods
Meaning of interpolation – Difference table – Newton’s forward interpolation formula (no deduction) –
roblems. – Introduction to numerical integration – Formulae for composite trapezoidal and Simpson’s 1/3 rule
(no deduction) – Related problems. – Numerical solution of non-linear equations – Formula for NewtonRaphson method (no deduction) – Problems. – Numerical solution of system of linear equation – GaussElimination Method (no deduction) – Problems.
Differential Equations
Definition – Order and degree of a differential equation – Differential equations of 1st order and 1st degree –separation of variables – Problems. – Homogeneous differential equations – Equations reducible to the
homogeneous form – Problems. – Exact differential equations – equations reducible to the exact form –
problems. – Linear equations – Bernoulli’s equations. – Differential equations of 2nd order with constant coefficients – Complementary function and particular integral – Problems.
Partial Differentiation
Function of two or more variables – Definition and meaning of partial derivatives (1st order). – Homogeneous
unctions – Euler’s theorem on homogeneous functions (no deduction) – Problems.
Probability and Statistics
Introduction – Random experiment – Sample space – Events. – Classical and axiomatic definition of
probability. – Addition and multiplication theorem – Related problems. – Statistics – Frequency distribution. –
Measure of central tendency – Mean – Median – Mode – Standard deviation – Simple problems.

E L E C T R I C A L T E C H N O L O G Y
Kirchoff’s Law
Kirchoff’s voltage and current laws, Star-delta transformations – Simple problems on all topics.
A. C. Fundamentals
Concept & significance of R.M.S. value, peak value, average value, crest factor and form factor of sinusoidal
voltage/current – Equation of instantaneous value of sinusoidal voltage/current – Simple problems on all.
A. C. Series Circuit
R-L & R-C A.C. series circuit (no deduction, only the expressions of voltage, current & power for sinusoidal
sources), power factor, power triangle – simple problems.
Storage Cell, Transformer, Motors etc.
Basic Principle of: Storage cell, D.C. motors, Transformer, A.C. generators & motors (No deduction &
problems).

Magnetic Circuit
Concept on magnetic circuit, Definitions and units of magnetic flux, m.m.t. and reluctance, analogy with
electrical circuit, simple problems.
Motor Starter
Need of motor starter mentioning some names useful for D.C. motors & A.C. motors.
Motors for Industrial Uses
Simple Electrical Circuit for motor installation, using block diagram of different components.
Power Generation, Transmission & Distribution
Brief idea about the power generation, transmission and distribution using block diagram of different stages.
Voltage Stabilizer & UPS System
Brief idea about the operational principle of voltage stabilizer and UPS system (no description of internal
circuit)
House Wiring
Simple idea house wiring starting from commencement of supply, using necessary diagram, role of fuses /
MCB, fault finding & earthing concept.
Lighting Schemes
Types of lighting scheme and factors considered for designing lighting schemes i.e. illumination level,
uniformity of illumination, colour of light, glare, mounting height, spacing between luminaries, colour of
surrounding walls etc.
Wattmeter & Meggar
Uses & connection diagram of Wattmeter – Use of Meggar with circuit diagram.
Electrical Energy Measurement
Electrical energy measurement (no mathematical deduction & description of apparatus) – circuit diagram for
single phase energy-meter connection.

C O M P U T E R A P P L I C A T I O N S
Introduction to Computer
Brief history of Evolution of computer — Various components of Computer (brief knowledge) -Hardware –
CPU, Input Output System, Primary Memory, Secondary Memory. Peripherals devices- Printers, Plotters,
Scanners, Digital Cameras, Sound Cards and Speaker System, Dicta phone. Software- Operating System,
System Software like compilers and Device Drivers, and various application software (application only).
Information Representation
Number System: Binary, Octal & Hexadecimal and conversion of number systems, Signed and unsigned
representation. Binary arithmetic and compliments. Character Codes : ASCII, BCD and Gray Codes.
Basic of Software
Classification of Software Systems – System Software and application software. Basic concepts of compilers,
interpreters, assemblers and device drives. Operating System – Single user, multi user, graphical user interface
and characters user interfaces. Case studies: MS – DOS, Windows.
Introduction to programming

Algorithm and flowchart. Different types of programming languages – Machine level, assembly level and high
level languages (basic concepts only). Brief introduction to different high level languages including C. Basic of
C-language. Branching and loping statements. Array and user defined functions.
Computer networking and internet
Basic of computer Networking – LAN, MAN, WAN (definitions only). Client – Server Architecture
(elementary level). Internetworking concepts of world wide web. Domain name system emails. Web browsing,
use of search engines, web site hosting (elementary level).

Adobe Scan 19-Jul-2023